Phone Icon
search Icon
×
Positioning icon Current location:HOME>BLOG>Measuring Protein and DNA in Microlitre Samples | HENG MEI Intelligent Manufacturing

Measuring Protein and DNA in Microlitre Samples | HENG MEI Intelligent Manufacturing

Article Source:Hengmei Laboratory Instrument Expert    Release time: 2026-11-16 18:00:50

Working at half a microlitre changes what is difficult. Sample conservation stops being a problem and everything else becomes one: the pedestal must be clean, the blank must match the buffer, the path length must suit the concentration, and the spectrum — not only the number — tells you whether any of it worked.

This article is a practical routine for protein and nucleic acid measurement in the microlitre range. It is written by the engineering team at HENG MEI Intelligent Manufacturing for laboratories that have moved from cuvettes to pedestals.

Choose the path length before pipetting

A micro-volume instrument offers several path lengths and normalises the result to a 10 mm equivalent. The choice controls whether the reading sits in a useful part of the detector's range.

Sample concentrationPath lengthReason
Purified protein at 10 mg/mL or above0.04 mmKeeps absorbance off-scale otherwise
Routine cell lysate, 1–10 mg/mL0.2 mmBest accuracy specification for this range
Dilute eluate, below 0.2 mg/mL1.0 mmIncreases signal at low concentration

Many instruments select automatically, and the manual override exists for a reason: when a result looks implausible, forcing a different path is the fastest way to establish whether the problem is the sample or the setting.

Blank against the buffer, always

A280 measurement assumes the only absorber in the drop is protein. Buffers break that assumption constantly: Tris absorbs in the UV, DTT and β-mercaptoethanol absorb below 250 nm, and guanidine and imidazole absorb strongly near 230 nm.

Blank with the exact buffer the protein is in, at the same dilution. Blanking with water inflates the reading, sometimes by a factor of two, and the error is invisible in the final number. Where a buffer cannot be avoided, a colorimetric assay (BCA or Bradford) measures protein independently of the UV background and is the correct alternative.

Micro-volume spectrophotometer measuring a microlitre protein sample on its pedestal

Read the spectrum when the number looks wrong

A single number hides the reason for a bad result; a scan shows it. Four patterns cover most problems.

  • Peak at 260 nm higher than 280 nm — nucleic acid contamination in a protein prep.
  • Strong absorbance near 230 nm rising sharply — guanidine, phenol or peptide backbone effects depending on context.
  • Rising baseline across the whole range — particulates or bubbles; the drop was not clean.
  • Flat trace near zero — no sample on the pedestal, or the pedestal was not engaged.

The full-spectrum configuration exists for this diagnostic role as much as for wavelength flexibility. A single-wavelength instrument reports a number; a scanning instrument explains it.

DNA measurement is not the same routine

For nucleic acids, the readings of interest are 260 nm for concentration and the 260/280 ratio for purity. Two cautions apply at microlitre scale.

First, the ratio becomes unreliable below roughly 10 ng/µL, because both terms approach the noise floor. Second, below about 2 ng/µL, absorbance is the wrong method entirely and a dye-based fluorescence assay should be used instead.

Where the sample is a small eluate from a low-input extraction, the honest approach is to measure by fluorescence for concentration and reserve absorbance for purity checks on the more concentrated samples.

OD600 in the same instrument

Culture density measurement is a frequent secondary need in laboratories that also quantify protein and DNA. An OD600 range of 0–4 Abs with stability and repeatability within 1% covers the exponential and early stationary phases of bacterial growth without dilution. Above 4 Abs, dilution into fresh medium is required — and the dilution must be recorded, because OD600 is linear only within a stated window.

Cleaning and carry-over

  1. Wipe the pedestal and the lid with a lint-free tissue between samples; protein films form quickly and bias subsequent readings upward.
  2. Run a water blank after a concentrated sample to confirm no residue remains.
  3. Do not let samples dry on the pedestal; dried protein is difficult to remove and leaves a permanent baseline offset.
  4. Re-check with a standard at the start of each session rather than assuming yesterday's calibration persists.

How HENG MEI supports microlitre workflows

HENG MEI Intelligent Manufacturing supplies micro-volume spectrophotometers with 0.5–2 µL sample volume, three path lengths and a 190–850 nm range on the full-spectrum model, plus OD600 capability for culture measurement. The configuration logic between fixed-wavelength and full-spectrum instruments is set out in our selection guide.

To choose a configuration, tell our sales contact the sample types, the concentration range, whether spectral diagnosis matters and whether OD600 is part of the routine.

Contact: Arthur, Sales Contact, Arthur@hmdzkj.cn, +86 18353666151 (Tel / WhatsApp / WeChat).


Article address:https://www.labinstruments.net/news/measuring-protein-dna-microlitre-samples.html